Will the micro switch release the source of interference
the micro switch is a low-current, low-voltage switching device in electronic equipment and industrial automation electrical equipment. due to its low operating frequency and relatively small control current, it generally does not produce electromagnetic interference and harmonic interference.
even if there is weak interference, the isolation transformer used in the control circuit and various filters installed in plc, touch screen and other components can also reduce the interference to a particularly low level, which is basically negligible.
according to the definition of interference, it can be seen that a signal is interference because it has an adverse effect on the system. otherwise, it cannot be called interference. it can be known from the factors that cause interference that eliminating any one of the three factors will avoid interference. anti-jamming technology is the three elements of research and processing.
devices that generate interference signals are called interference sources, such as transformers, relays, microwave equipment, motors, cordless phones, high-voltage lines, etc., which can generate electromagnetic signals in the air. of course, lightning, the sun, and cosmic rays are all sources of interference.
the formation of interference includes three elements: interference source, transmission path and receiving carrier. without any of these three elements, there will be no interference.
the propagation path refers to the propagation path of the interference signal. electromagnetic signals propagate in a straight line in the air, and penetration propagation is called radiation propagation; the process of electromagnetic signals propagating into equipment through wires is called conduction propagation. the route of transmission is the main reason for the spread and ubiquity of interference.
the control panel or touch screen is a receiving carrier, which means that a certain link of the affected equipment absorbs interference signals and converts them into electrical parameters that affect the system. the receiving carrier cannot perceive the interference signal or weaken the interference signal, so that it is not affected by the interference, and the anti-interference ability is improved. the receiving process of the receiving carrier becomes coupling, and the coupling can be divided into two types: conductive coupling and radiation coupling. conduction coupling means that electromagnetic energy is coupled to the receiving carrier through metal wires or lumped elements (such as capacitors, transformers, etc.). ) in the form of voltage or current. radiation coupling means that electromagnetic interference energy is coupled to the receiving carrier in the form of electromagnetic field through space.
in the working environment of the mechatronics system, there are a lot of electromagnetic signals, such as the fluctuation of the power grid, the start and stop of high-voltage equipment, the electromagnetic radiation of high-voltage equipment and switches, etc. when they produce electromagnetic induction and interference shocks in the system, they will often disrupt the normal operation of the system, which may cause system instability and reduce the accuracy of the system.
it can be seen from the above that micro-switches generally do not produce electromagnetic interference and harmonic interference.
梁瑾侧风道高压鼓风机总结了以下几个选型注意事项
大气颗粒物采样器如何采样
分流量雨污水截污，一体化截流井大显身手
DMML-16-25-P-A现货DMML
在线湿度仪
Will the micro switch release the source of interference
ALMATEC气动隔膜泵CXM20FES选型说明
您了解鱼塘增氧气泵应用底层微孔曝气增氧的几大优势吗
揭开单斗式上料机的神秘面纱
公路、城市道路摆式混凝土路面砖摩擦系数测定仪
120吨/天污水处理一体化设备
电子天平如何选择？以下方面需要清楚
汽车阻火器功能
步入式恒温恒湿控制室的温湿度系统的使用范围和调控
丝印油墨性能的测定
东材科技两大重磅项目投资超3亿元！
冻干机的使用准备及维护方法
烘干法腐竹快速水分检测仪标准方法
记录仪通电后会对系统各部件及接口进行检测
易福门电感式接近开关IIT200京南华建现货
even if there is weak interference, the isolation transformer used in the control circuit and various filters installed in plc, touch screen and other components can also reduce the interference to a particularly low level, which is basically negligible.
according to the definition of interference, it can be seen that a signal is interference because it has an adverse effect on the system. otherwise, it cannot be called interference. it can be known from the factors that cause interference that eliminating any one of the three factors will avoid interference. anti-jamming technology is the three elements of research and processing.
devices that generate interference signals are called interference sources, such as transformers, relays, microwave equipment, motors, cordless phones, high-voltage lines, etc., which can generate electromagnetic signals in the air. of course, lightning, the sun, and cosmic rays are all sources of interference.
the formation of interference includes three elements: interference source, transmission path and receiving carrier. without any of these three elements, there will be no interference.
the propagation path refers to the propagation path of the interference signal. electromagnetic signals propagate in a straight line in the air, and penetration propagation is called radiation propagation; the process of electromagnetic signals propagating into equipment through wires is called conduction propagation. the route of transmission is the main reason for the spread and ubiquity of interference.
the control panel or touch screen is a receiving carrier, which means that a certain link of the affected equipment absorbs interference signals and converts them into electrical parameters that affect the system. the receiving carrier cannot perceive the interference signal or weaken the interference signal, so that it is not affected by the interference, and the anti-interference ability is improved. the receiving process of the receiving carrier becomes coupling, and the coupling can be divided into two types: conductive coupling and radiation coupling. conduction coupling means that electromagnetic energy is coupled to the receiving carrier through metal wires or lumped elements (such as capacitors, transformers, etc.). ) in the form of voltage or current. radiation coupling means that electromagnetic interference energy is coupled to the receiving carrier in the form of electromagnetic field through space.
in the working environment of the mechatronics system, there are a lot of electromagnetic signals, such as the fluctuation of the power grid, the start and stop of high-voltage equipment, the electromagnetic radiation of high-voltage equipment and switches, etc. when they produce electromagnetic induction and interference shocks in the system, they will often disrupt the normal operation of the system, which may cause system instability and reduce the accuracy of the system.
it can be seen from the above that micro-switches generally do not produce electromagnetic interference and harmonic interference.
梁瑾侧风道高压鼓风机总结了以下几个选型注意事项
大气颗粒物采样器如何采样
分流量雨污水截污，一体化截流井大显身手
DMML-16-25-P-A现货DMML
在线湿度仪
Will the micro switch release the source of interference
ALMATEC气动隔膜泵CXM20FES选型说明
您了解鱼塘增氧气泵应用底层微孔曝气增氧的几大优势吗
揭开单斗式上料机的神秘面纱
公路、城市道路摆式混凝土路面砖摩擦系数测定仪
120吨/天污水处理一体化设备
电子天平如何选择？以下方面需要清楚
汽车阻火器功能
步入式恒温恒湿控制室的温湿度系统的使用范围和调控
丝印油墨性能的测定
东材科技两大重磅项目投资超3亿元！
冻干机的使用准备及维护方法
烘干法腐竹快速水分检测仪标准方法
记录仪通电后会对系统各部件及接口进行检测
易福门电感式接近开关IIT200京南华建现货